The Role of Nitrogen in Preventing Corrosion in Pipe Systems – an Unbiased Perspective
Introduction
Internal pipe corrosion results in significant operational and financial consequences across industries. From pinhole leaks to system-wide failures, corrosion contributes to equipment damage, water quality degradation, and costly downtime.
Traditional corrosion control relies on proper pipe pitch and low point drains, chemical treatments, air dryers (e.g. desiccant filters) and coatings. Nitrogen, a relative newcomer in the industry, has garnered a lot of attention but most information available on its capabilities comes from nitrogen generator manufacturers and is thereby prone to overstatement of capabilities to foster equipment sales. Let’s dive deeper into the use of nitrogen as a corrosion inhibitor in pipe systems from an unbiased resource.
How Nitrogen Prevents Corrosion
Corrosion is typically an electrochemical process that requires oxygen and water. When both are present inside a pipe system (especially in systems that remain stagnant or are partially filled with air and water), they react with metal surfaces, leading to rust (i.e. oxygen corrosion), corrosion build-up, and internal wall loss.
Nitrogen corrosion prevention works by:
Displacing oxygen in fire protection systems
Creating an inert atmosphere that reduces oxidation
Reducing the conditions favorable for Aerobic Microbiologically Influenced Corrosion (MIC), which often requires both water and oxygen
Drying traces of residual water
Nitrogen is dry, stable, and non-reactive—making it ideal for maintaining an internal environment that is inhospitable to corrosion.
Using nitrogen to prevent corrosion in piping systems can be beneficial in stopping or slowing future corrosion development, but there are deficiencies of nitrogen that are rarely discussed.
1. Does Not Reverse Existing Damage
Nitrogen prevents further corrosion by displacing oxygen, but it cannot repair or reverse existing corrosion issues, such as:
Pitting
Wall thinning
Removal of existing corrosion build-up obstructing water flow
Internal scaling or tuberculation
Micro-cracks caused by long-term corrosion
Existing weaknesses remain in place and may still lead to leaks, clogged sprinkler heads, reduced water flow, or structural failure.
2. Does Not Stop Existing Corrosion
While nitrogen is very effective at preventing new corrosive activity, it is not particularly effective at stopping existing corrosion. This is due to the manner in which nitrogen interacts with the corrosive process inside of a piping system. As mentioned earlier, nitrogen works by displacing oxygen, a key component in the corrosion equation. The issue arises when corrosion advances enough to generate tubercules that act as a “biodome” protecting the corrosive process much like scuba gear protects a diver from drowning. Nitrogen will displace oxygen within the piping system but has no impact under nodules where the corrosive activity is occurring.

3. Traps Corrosion Byproducts
In older, corroded systems, nitrogen can stabilize an anaerobic environment where sulfate-reducing bacteria (SRB) may still thrive, potentially exacerbating aneroobic MIC if not fully flushed or chemically treated beforehand.
4. May Create a False Sense of Security
Implementing nitrogen in a corroded system can delay visible failure, which may mislead operators into thinking the system is now safe. If an inspection isn’t included as a component of nitrogen installation, serious damage could remain undetected.

5. Incompatibility with Poorly Maintained Systems
Nitrogen is effective in sealed, dry, or well-maintained environments but the effectiveness is reduced in systems with:
Leaks
Severe corrosion
Poor drainage or large water pockets
Active water ingress
6. Limited Effectiveness in Wet Systems
Nitrogen is occasionally recommended in wet-pipe fire protection systems to replace oxygen at system high points. This is not a terribly effective approach as oxygen is continuously introduced via dissolved air in water. Time proven methods such as proper pitch and venting are much more effective tools to keep the system healthy.
7. Cannot Remove Scale or Deposits
Corrosion scale and mineral buildup from earlier degradation can impede flow, harbor bacteria, or hide further corrosion underneath. Nitrogen does not clean or remove these materials.
8. Trapped water
While nitrogen has a dewpoint as low as -94°F (depending on purity) and can remove trace amounts of water or dry out sludge, the capabilities of nitrogen to remove large amounts of trapped water is often overstated and creates a false sense of security. To effectively remove water from a dry or pre-action system, large pockets of trapped water must first be drained and the system should be properly pitched to address future issues. Any sludge in the system needs to be removed to prevent obstruction when the system is activated.
9. Purge Valves
To reach effective levels of nitrogen in closed systems such as fire suppression, multiple purge valves are necessary to vent out air allowing the system piping to be filled with 99%+ nitrogen. Some companies claim a single valve is all that is required to somehow magically vent an entire system, but the reality is that many vents are needed to effectively purge air from the whole system. These vents add substantial load to the air compressor to maintain supervisory pressure increasing the flow through the “generator”, requiring more frequent filter changes and also adding new potential points of failure at each purge valve.
10. Plumbing Code Adherence
Depending on how your AHJ interprets the Uniform Plumbing Code, it is possible that a reduced pressure backflow preventer will have to be installed to prevent cross contamination with the potable water supply. The addition of a reduced pressure backflow preventer in a fire suppression system will require a hydraulic recalculation and possibly the addition of a costly fire pump to maintain proper water supply to the system. More information on the specifics of the code can be found by researching UPC 603.4.16.3 and 603.4.16.4.
Recommended Actions in Corroded Systems to Effectively Use Nitrogen
If nitrogen is being considered for an existing system:
First: Perform a thorough internal inspection (e.g., ULGW, borescope, or visual analysis) to evaluate for trapped air/water and the extent of existing system damage
Second: Replace compromised piping in severely corroded systems
Third: Clean and treat the system if microbial activity or debris is present
Fourth: Assure system is pitched properly and that low points have drains or wet systems are properly vented
Finally: Use nitrogen as part of a long-term corrosion management strategy with a healthy system—not as a standalone “snake oil” cure. Like painting a rusty car, proper preparation in advance is the key step that must be taken for prolonged success.
Conclusion
Nitrogen is excellent for prevention, but not a cure for active or advanced internal corrosion. Its use in corroded systems should be approached cautiously and always paired with inspection, cleaning, and possible repairs or replacement of severely damaged piping.
Inspection and Verification
Although nitrogen systems drastically reduce corrosion risk, verification is still essential. Technologies like Ultrasonic Localized Guided Wave (ULGW) testing allow non-invasive, internal assessment of pipe conditions—ensuring the effectiveness of nitrogen corrosion mitigation strategies.
